A dropped stitch doesn’t mean ripping back the whole piece. In most cases you can rescue it with a crochet hook in under a minute. The stitch slides off the needle, and if you don’t catch it, it runs down through the rows below like a ladder in a stocking. But every rung of that ladder is a strand of yarn waiting to be pulled back through, one row at a time, until the stitch is back on the needle.
To fix a dropped stitch, insert a crochet hook through the loose loop, catch the horizontal strand behind it, and pull it through. Repeat for each row the stitch has run down. Keep a crochet hook in roughly the same size as your knitting needles in your notions bag. You’ll use it.
Fixing a dropped knit stitch
The most common situation. A stitch has slipped off and run down on the knit (right) side of stockinette.
Insert the crochet hook through the dropped stitch from front to back. The loose horizontal strand (the ladder rung) sits behind the stitch. Hook the strand and pull it through. One row recovered.
If the stitch ran multiple rows, there are multiple strands stacked behind it. Work each one from bottom to top, pulling it through the stitch on the hook. When you’ve worked all the strands, the stitch is back at the current row. Slide it from the hook onto the left needle, making sure it’s not twisted (right leg in front of the needle).
Fixing a dropped purl stitch
Same repair, reversed direction. The dropped stitch is on the purl side (wrong side of stockinette, or a purl column in ribbing).
Insert the hook through the stitch from back to front. The strand sits in front this time. Hook it and pull through.
Purl-side repairs can feel fiddly. One workaround: turn the work so the purl side becomes the knit side, fix it as a knit stitch (the easier direction), turn back. Same result.
Fixing a dropped stitch in garter stitch
Garter alternates knit and purl rows, which means the ladder strands alternate between sitting behind and in front of the stitch. You can’t pull every strand from the same direction.
Work one strand as a knit stitch (hook from front, strand behind). Next strand as a purl stitch (hook from back, strand in front). Alternate for each row.
If you lose track: look at the stitch you just made. Purl bump at the top means the next strand goes through as knit. Smooth V means the next one goes through as purl.
Slower and more error-prone than stockinette. Take each strand individually.
Fixing a dropped stitch in ribbing
Ribbing is columns of alternating knit and purl stitches. Figure out whether the dropped stitch belongs to a knit column or a purl column by looking at the stitches on either side.
Knit column: fix as a series of knit stitches (strand behind, hook forward). Purl column: fix as a series of purl stitches (strand in front, hook backward). Don’t alternate like garter. Each column is consistent.
Catching it before it runs
A dropped stitch that hasn’t run yet (live loop sitting below the needle, no ladder) is the easiest fix. Slip it back onto the left needle. Done. No ladder to work up.
To spot dropped stitches early: glance at your needle periodically. A missing stitch shows as a gap and a loose strand where the stitch should be. Catching it within a row or two means a quick fix. Twenty rows later means a long ladder.
Stitch markers help. Place one every 20 stitches and you only need to count within a small section to find the problem. KnitTools’ Row Counter can track stitch counts at checkpoints.
When a stitch runs to the cast-on edge
If the stitch ran all the way down and there’s no loop at the bottom, you can still fix it. Use the hook to pull the bottom strand through itself to create a new base loop, then work each strand above it. The base loop differs slightly from a cast-on stitch in structure, but it’s stable and invisible after blocking.
If the run has gone far and the strands are tangled, pin the area with a locking stitch marker to prevent more damage while you work the repair.
When to frog instead
Not every dropped stitch is worth fixing in place. If it dropped in a complex cable or lace pattern, the repair needs to recreate the exact stitch sequence (yarn overs, decreases, cable crosses) for every row it ran through. That can be harder than ripping back.
For plain stitches (stockinette, garter, ribbing) in smooth yarn, the crochet hook fix works every time. For textured patterns, it depends on how many rows you’d reconstruct and how complex each row is. Two rows of a cable: fixable. Ten rows of a complex lace chart: probably faster to frog.
Fuzzy yarn (mohair, brushed alpaca) makes repairs harder because the fibers cling and resist being pulled through cleanly. Work slowly with a hook slightly smaller than you’d normally use.
FAQ
Do I need a specific crochet hook size? Close to your needle size or slightly smaller. Too large won’t fit through the stitch. Too small and you can’t grab the strand. Exact match not required.
Will the fixed stitch look different? Sometimes slightly. Tension in the repaired stitches may be uneven because you’re pulling yarn through by hand. Blocking usually evens this out. If a stitch looks tight or loose, tug the surrounding stitches to redistribute yarn.
Can I use a knitting needle instead? For one row, yes. Pick up the stitch and strand on the needle tip and pass one through the other. For multiple rows, a crochet hook is far easier because the hook grabs and pulls in one motion.
What if I twist the stitch putting it back? A twisted stitch sits with its legs crossed (left leg in front). It produces a tighter, slightly angled stitch. If you notice, slip it off, rotate, put it back. If you don’t catch it until later, it’s a minor cosmetic issue most people won’t notice.